In this article below you will discover a lot of decent points regarding How to Install a Bathtub Yourself.
Setting up a tub isn't specifically brain surgery, yet it does require solid plumbing, woodworking, and also in some cases, tiling abilities. Replacing an old tub with a new one is also a moderately difficult job. If the old tub is easily accessible, the project can relocate speedily; if you have to open up a wall surface to get rid of the old bathtub as well as place the brand-new tub, the job is a lot harder. In either situation, the job is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub and set in the new one. Make certain you have actually qualified on your own for the job and fit trying it. Instead of working with a professional to take over a halfway-completed project, it is better to take into consideration utilizing one before you start. Opportunities are you may require a specialist plumber to make tube connections.
This write-up will aid you mount a brand-new tub in your shower room if you have currently acquired a new tub as well as do not require to transform the plan of your previous water system pipelines.
Your tools and material checklist ought to consist of the following:
Getting ready for the Installment
Firstly, the sustaining frame provided with the bathroom should be fitted (if required) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is essential to make certain that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a sustaining plate under the faucets device to avoid stress on the bathtub.
Fit the adaptable tap adapters to the bottom of both taps using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you should do is detach the water system. After doing so, activate the taps to drain any water staying in the system. The process of removing the existing taps can be quite problematic because of the limited accessibility that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipelines. When the supply pipes have been removed, utilize the exact same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the solitary faucets from transforming during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any kind of old sealing substance.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Mounting the Bathtub
Utilizing the two wooden boards under its feet, put the tub in the needed placement. The wood boards are useful in evenly spreading out the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four tiny factors.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by examining the spirit level as well as adjusting the feet on the tub until the spirit level reviews level.
To mount taps, fit the bottom of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression join; after that do the exact same for the other faucet.
Activate the supply of water and also check all joints and also brand-new pipework for leakages and tighten them if required. Fill the tub as well as additionally check the overflow electrical outlet as well as the regular electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the manufacturer's instruction manual. Tiling as well as sealing around the bathtub needs to wait up until the bath tub has actually been used at the very least when as this will certainly resolve it into its last position.
Fitting New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the faucet in the installing hole in the bath/basin guaranteeing that the washers are in location in between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. When the tap is firmly in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former type needs to be connected to the faucet ends initially, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to break an inflexible seal, triggering the water to pass through the wall in between the bath and also the tiling, bring about difficulties with moisture and possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealers to assimilate your components and fittings. They are offered in tubes and also cartridges, as well as can sealing voids approximately a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of drenched newspaper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack rather very early if you do not take into consideration this motion prior to securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are also conveniently offered on the market. It is advisable to fit the tiles making use of water-resistant or water resistant glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub? Post a review below. We will be pleased to hear your responses about this blog. Hoping that you visit us again before long. Appreciated our blog entry? Please share it. Let another person discover it. Thank you for your time spent reading it.
Top plumbers, call!